SHACMAN Delong X5000 620HP 6×4 Heavy‑Haul Tractor Head
video

SHACMAN Delong X5000 620HP 6×4 Heavy‑Haul Tractor Head

Heavy‑haul prime mover engineered for super‑heavy and oversized transport duty, purpose‑built to pull lowbed semi‑trailers, hydraulic modular axle‑line trailers and detachable‑gooseneck combinations on long‑distance highway runs and difficult project‑site access roads. Built on the Delong X5000 platform with the reinforced 8+7 double‑layer frame, hub‑reduction tandem drive axle and 13.54 L WEICHAI diesel engine. Driveline specification, axle ratio, power take‑off, retarder, fifth‑wheel rating and cab trim are configurable per haulage assignment. There is no single universal build sheet; the tractor is specified around cargo gross weight, trailer type, route gradients, permitted axle loads and destination‑market emission and steering regulations.
Send Inquiry
Product Introduction

JUTONG Heavy‑haul prime mover engineered for super‑heavy and oversized transport duty, purpose‑built to pull lowbed semi‑trailers, hydraulic modular axle‑line trailers and detachable‑gooseneck combinations.

This tractor head is built on the SHACMAN Delong X5000 platform and adopts the reinforced 8+7 double‑layer chassis frame together with a HANDE hub‑reduction tandem axle. The 13.54 L WEICHAI WP14H engine delivers 620 HP and approximately 2,800 N·m of torque low in the rev band, giving strong breakaway and gradient capability at crawling speed. Axle ratio, power take‑off provision, hydraulic retarder, fifth‑wheel rating and cab configuration are finalised against the actual haulage contract. No fixed universal specification applies; the build sheet is engineered around cargo tonnage, trailer interface, terrain profile, statutory axle‑load caps and the emission and hand‑of‑drive requirements of the destination market.

Parameter Category

Specification Details

Vehicle Model SHACMAN Delong X5000 620HP 6×4 Tractor Head (Elite Version / Super Strong Version)
Homologation Code SX4259XD4C1
Drive Configuration 6×4
Engine WEICHAI WP14H620E68, in-line 6-cylinder, 13.54 L, China VI
Max Power 456 kW (620 HP)
Peak Torque Approx. 2,800 N·m (delivered in the 1,000–1,400 r/min range)
Transmission FAST S13MD, 13 forward speeds + 2 reverse, manual, iron housing
Retarder FAST hydraulic retarder (optional)
Drive Axle HANDE 13 t single-reduction tandem, ratio 5.262 (standard)Heavy-haul version: optional 25 t HANDE double-reduction (hub-reduction) tandem, ratio 6.733
Chassis Frame (970–850)×300×(8+7) mm double-layer reinforced main beam
Leaf Springs Front 10 / Rear 12 leaves
Wheelbase 3,375 + 1,400 mm
Safety Features ABS, ESC, inter-axle / inter-wheel differential locks, FCW forward collision warning, LDWS lane departure warning, BeiDou telematics recorder
 
IMGE0939
 
 
IMGE0940
 
 
IMGE0944
IMGE0954

 

 

Typical Applications

 

 

 

Oversized Machinery Haulage: Towing lowbed and detachable‑gooseneck semi‑trailers for excavators, bulldozers, piling rigs and mining plant between equipment yards and remote job sites.

Super‑Heavy Project Cargo: Matched with multi‑axle hydraulic modular trailers for transformers, generator stators, reactor vessels and other indivisible loads requiring permit‑based movement.

Long‑Distance Heavy Corridor Transport: Sustained high‑torque output and large fuel capacity support multi‑day highway transits across regions with limited fuelling infrastructure.

Rough‑Terrain and Mountain Routes: Hub‑reduction gearing and double‑layer frame provide the tractive effort and structural margin demanded by steep gradients, unpaved access roads and heavily rutted site entries.

 

 

Key Product Functions

 

 

High‑Torque Low-Speed Driveline

• Large Displacement Engine: The 13.54 L in‑line six delivers peak torque from 1,000 r/min, so the combination can move off from standstill under extreme load without clutch abuse.

• Hub‑Reduction Final Drive: Wheel‑end reduction multiplies output torque at the wheel, giving the crawling capability needed to inch a loaded modular trailer through site gates and gradients.

• Matched Ratio Options: 6.733 for heavy haul, 5.262 for standard duty - final drive selection is locked to the intended duty cycle rather than left to default.

Reinforced Chassis Structure

Heavy haul applies concentrated bending and torsional load through the fifth wheel into the frame rails. The 8+7 double‑layer main beam, together with reinforced cross‑members, is engineered to resist long‑term fatigue under repeated overload cycles rather than merely survive a single trip.

Evaluated design parameters include: Cargo gross weight and trailer tare contribution Fifth‑wheel vertical and longitudinal load transfer Route gradient profile and average speed requirement Permitted axle loads and bridge weight ratings along the corridor Ambient temperature, altitude and fuel quality of the operating region

Trailer Interface and Hydraulic Integration

• Reinforced Fifth Wheel: Higher‑rated coupling plate distributes kingpin load across a wider frame footprint, reducing local stress concentration.

• Power Take‑Off Provision: An optional PTO drives hydraulic pumps for modular axle‑line trailers, detachable goosenecks, loading ramps and recovery winches.

• Matched Electrical Interface: 24 V trailer socket, ABS/EBS signal line and auxiliary lighting circuit pre‑configured for heavy trailer combinations.

Gradient Control and Braking Safety

• Hydraulic Retarder: Continuous auxiliary braking on long descents keeps service brakes cool and preserves full emergency braking capacity.

• Engine Braking Plus ABS/ESC: Combined retardation strategy shortens stopping distance on loaded downgrades and reduces jack‑knifing risk.

• Differential Locks: Inter‑axle and inter‑wheel locks maintain traction on loose gravel, mud and ice where a single spinning wheel would otherwise stall the combination.

Driver Environment for Long Heavy Duty

• Air‑Suspended High‑Roof Cab: Four‑point air mounting and air‑suspended seat reduce whole‑body vibration over long heavy‑haul shifts.

• Extended Fuel Autonomy: 800 L standard, 1,100 L optional, cutting refuelling stops on corridors with sparse service networks.

• Telematics and Warning Systems: Forward collision warning, lane departure warning and BeiDou recording support fleet monitoring and insurance compliance.

 

Manufacturing and Quality Control

 

 

Frame Fabrication: Double‑layer main beams are cut and drilled on CNC lines, then riveted and welded to controlled dimensional tolerance before chassis assembly.

Driveline Assembly: Engine, transmission and hub‑reduction axle are installed as a matched powertrain set, with torque‑to‑spec tightening recorded at each coupling point.

Wheel Alignment and Ratio Verification: Tandem axle parallelism and final drive ratio are verified against the build sheet to prevent premature tire wear and driveline wind‑up.

Load and Brake Testing: Gross combination load simulation, service brake performance and retarder function are validated on the factory test line.

Pre‑Delivery Inspection: Full electrical circuit, hydraulic PTO circuit (where fitted), lighting, cab functions and fluid levels are checked and documented before shipment.

 

FAQ

 

Q: What is a 620 HP 6×4 heavy‑haul tractor head?

A: It is a three‑axle prime mover specified with a reinforced frame, hub‑reduction drive axle and high‑torque diesel engine, intended to pull lowbed, gooseneck and modular axle‑line trailers under permit‑based heavy loads.

Q: Why is the homologated GCW only 38.27 tonnes?

A: That figure is the regulatory type‑approval limit for normal road registration. Actual heavy‑haul capacity is determined by the oversize/overweight permit issued for a specific route, and by the axle configuration of the trailer in use.

Q: Do I need the 6.733 hub‑reduction axle or the 5.262 single‑reduction axle?

A: Choose the 6.733 hub‑reduction tandem for crawling heavy haul and steep site access; choose the 5.262 single‑reduction tandem only for lighter duty or higher‑speed highway work.

Q: Is a power take‑off required?

A: Yes if the tractor will operate hydraulic modular trailers, detachable goosenecks, powered ramps or winches. Specify PTO at order stage; retrofitting afterwards is costly.

Q: Which emission and steering versions are available for export?

A: China VI is standard domestically; Euro II to Euro V configurations are available for markets without advanced fuel or AdBlue infrastructure. Right‑hand‑drive build is offered for RHD markets.

 

Hot Tags: shacman delong x5000 620hp 6×4 heavy‑haul tractor head, China shacman delong x5000 620hp 6×4 heavy‑haul tractor head manufacturers

Send Inquiry

whatsapp

Phone

E-mail

Inquiry